T's in CAT's

FRED · Post by **FRED** » Mon Mar 21, 2016 10:44 am

Thank You Lyle, pictures are great ,pretty well what I want to put on my T.I don't know how to post pictures on this site otherwise I would show you my T.I have built my T with many used parts .mine well never be show quality but a good reliable and driving bucket.Hopefully I figure out how to post pictures.

mike wade · Post by **mike wade** » Mon Mar 21, 2016 10:56 am

FRED wrote:Thank You Lyle, pictures are great ,pretty well what I want to put on my T.I don't know how to post pictures on this site otherwise I would show you my T.I have built my T with many used parts .mine well never be show quality but a good reliable and driving bucket.Hopefully I figure out how to post pictures.

http://nationaltbucketalliance.com/bb/v ... =35&t=1012

Fred read this link for posting photos to this site........I think this will help you do it.........

Mike

IdahoRelic · Post by **IdahoRelic** » Mon Mar 21, 2016 11:44 am

Amen on posting pix. I managed to stumble through the first time. Now it's much easier. Mike's advice is dead on.

One thing you may have to watch is the size (pixel count) of your pic. If to big, the site will not allow you to post. I have had to reduce the size of all mine, so far......lyle

IdahoRelic · Post by **IdahoRelic** » Mon Mar 21, 2016 4:24 pm

Here ya' go Fred. I was wrong about the size of the oak boards! They actually measure 13".
I have added 1" angle braces in all four corners and on the top piece that the hinge is screwed to.
Using plywood for the top was a mistake, screws do not work well horizontally into plywood, should have used laminated pine available at Lowes/Home Depot

Next revision it will be replaced, and that piano hinge will be replaced with a hurricane galley hinge.
Any questions don't be afraid to ask. Have you figured out how to post a pic yet??.....lyle

IdahoRelic · Post by **IdahoRelic** » Mon Mar 21, 2016 4:27 pm

Oh, did you notice my hi tech lid prop

A left over piece of oak from the top trim. Works great, low maintenance too

I sliced off some 1/16x3/4 pieces from the left over oak and glued them to the floor, then set the battery on top of them. Made the battery mounts from 1/8x1" angle and a piece of 1/8 plate.

FRED · Post by **FRED** » Mon Mar 21, 2016 8:15 pm

I am still having trouble with the pictures,my problem is Igo to my picture files,I cant figure out how to move them from the files. I will keep working on it.Thanks for the detailed pictures of the box.Looks great,I like the size for holding gear.My bucket has ron popes extended body so I want the box to look proportion to the body.thanks again

IdahoRelic · Post by **IdahoRelic** » Mon Mar 21, 2016 8:25 pm

Fred, send me a pic. lhp2658@q.com I'll see what I can do to post it.....lyle

IdahoRelic · Post by **IdahoRelic** » Tue Mar 22, 2016 12:36 am

This is Fred's T to Be

rbsWELDER · Post by **rbsWELDER** » Tue Mar 22, 2016 7:09 am

What vehicle is Fred's seat out of?

Thanks,

IdahoRelic · Post by **IdahoRelic** » Tue Mar 22, 2016 9:53 am

I noticed that last night, too Mark.... I think Fred will see your post and he can answer directly.......lyle

National T-Bucket Alliance

T's in CAT's

Re: T's in CAT's

Re: T's in CAT's

Re: T's in CAT's

Re: T's in CAT's

Re: T's in CAT's

Re: T's in CAT's

Re: T's in CAT's

Re: T's in CAT's

Re: T's in CAT's

Re: T's in CAT's